***** How to install the device driver under DOS environment ***** To operate TEAC CD-ROM,the device driver (TEAC_CDI.SYS) has to be installed from INSTALLATION DISK came along with CD-ROM. Please follow the instruction below. 1. Boot up the system and insert the INSTALLATION DISK into your floppy disk drive. 2. At the DOS prompt,type "A:\INSTALL" then press enter. (If your floppy disk drive is "A:") 3. Installation program will now start.Please follow the instructions on the screen to complete the installation procedure. 4. When finish,remove the INSTALLATION DISK from the floppy disk drive then REBOOT your system. During system reboot,check for the following message to assure that the driver was loaded properly. MSCDEX Version 2.23 Copyright (C) Microsoft Corp. 1986-1993. All rights reserved. Drive X: = Driver TEAC-CDI unit 0 * 'X:' ... Drive letter assigned to CD-ROM Drive This message means that TEAC CD-ROM drive is now activated. * Now the installation of TEAC CD-ROMdrive is completed. ***** TEAC CD-ROM DRIVE Trouble Shooting Tips ***** ------------------------------------------------------------------------------ Q1: System will not boot when CD-ROM drive is daisy-chained with hard disk drive. ------------------------------------------------------------------------------ A1: Be sure your hard disk drive jumper is set to MASTER and CD-ROM's to SLAVE. Please refer to the installation manual for CD-ROM jumper setting and ask hard drive manufacturer for MASTER jumper setting. Note: There may be a case where CD-ROM can not be daisy-chained with Conner hard drive (Conner mode). A2: Check if the I/F cable is connected reversely. ------------------------------------------------------------------------------ Q2: System hangs without displaying anything when the device driver is loaded during Boot-up. ------------------------------------------------------------------------------ A1:There is a possibility that TEAC device driver is having a conflict with others. Please check the position of the device driver statement or remark driver which may be having a conflict with. A2:In case that TEAC CD-ROM drive is connected with non TEAC CD-ROM drive in the same system. Please re-install the TEAC CD-ROM address by going through 'SELECT I/O PORT'. ------------------------------------------------------------------------------ Q3: "Not Install Device Driver" message is displayed during loading the device driver. ------------------------------------------------------------------------------ A1:Please make sure that Power cable and I/F cable are properly connected. A2:Please make sure that there is no conflict with IDE card address (primary, secondary, tertiary etc.) and/or interrupt. A3:In case that CD-ROM drive is daisy-chained with hard disk drive, please make sure that hard disk drive jumper is set to MASTER and CD-ROM's to SLAVE. Please refer to the installation manual for CD-ROM jumper setting and ask hard drive manufacturer for MASTER jumper setting. A4:In case that your IDE I/O address is set to Tertiary/Quaternary, please re-install the TEAC CD-ROM Software to change the address by selecting 'SELECT I/O PORT'. A5:There will be the case where TEAC CD-ROM drive will not work with IDE Controller card with Cache. ------------------------------------------------------------------------------ Q4: CD-ROM drive will not be recognized by the system when MSCDEX.EXE is loaded. ------------------------------------------------------------------------------ A: Drive names specified in Config.sys and Autoexec.bat may not be matching. Please make sure that each statement has "/D:TEAC-CDI" ------------------------------------------------------------------------------ Q5: System does not recognize the CD-ROM drive with error message "Not enough drive letters". ------------------------------------------------------------------------------ A: There may be no more Drive letter available. Please add or edit "LASTDRIVE" statement so that the last drive equals one more than your current last drive. (Example) Current New A:FDD A:FDD B:FDD B:FDD C:HDD C:HDD D:HDD D:HDD E:CD-ROM -> "LASTDRIVE=E" ------------------------------------------------------------------------------ Q6: Getting the display "CDR101: Not Ready" when CD-ROM is accessed. ------------------------------------------------------------------------------ A: Please make sure that the disk is inserted in the drive or is not placed up side down. ------------------------------------------------------------------------------ Q7: Getting the display "CDR103: CD-ROM not High Sierra or ISO 9660 format" when CD-ROM is accessed. ------------------------------------------------------------------------------ A: This message will be displayed when non-standard CD is accessed. (Example) Placing Audio CD and accessing it without going into CDPLAYER. ------------------------------------------------------------------------------ Q8: CD-ROM drive is not recognized when RAM Boost is used. ------------------------------------------------------------------------------ A: Please insert the TEAC device driver statement before Ram Boost statement in your Config.sys. ------------------------------------------------------------------------------ Q9: Do I need BIOS CMOS Setup for my IDE CD-ROM ? ------------------------------------------------------------------------------ A: No,CD-ROM is not supported by BIOS.It is different from Hard Disk Drive. Please select "none" for BIOS Setup of CD-ROM I/O port. ------------------------------------------------------------------------------ Q10: CD-PLAYER for Windows will not work. ------------------------------------------------------------------------------ A: To operate CD-PLAYER for Windows,[MCI]CD Audio has to be installed in Drivers in Control Panel.Please refer to Windows manual to install [MCI]CD Audio. ------------------------------------------------------------------------------ Q11: How can I see Photo CD ? ------------------------------------------------------------------------------ A: You have to use Photo CD access software released from Kodak,Corel or Adaptec to see Photo CD. ------------------------------------------------------------------------------ Q12: How can I see CD-I/Video CD ? ------------------------------------------------------------------------------ A: You need MPEG Playback Card (Ex.RealMagic) to play CD-I/Video CD/Karaoke CD. You can see a directory of Video CD but not of CD-I. ------------------------------------------------------------------------------ Q13: I can't play CD-I. ------------------------------------------------------------------------------ A: There are two kinds of Disk.One is called CD-I which you have to use CD-I player and the other is CD-I Digital Video which you can play with CD-ROM drive and MPEG Playback Card. ------------------------------------------------------------------------------ Q14: Video CD Ver.2.0 can be played ? ------------------------------------------------------------------------------ A: It depends on your MPEG Playback Card. ------------------------------------------------------------------------------ Q15: Will CD-ROM drive work with i386 system ? ------------------------------------------------------------------------------ A: Yes,it will work with i386 but i486 or higher system is recommended to get better performance. ------------------------------------------------------------------------------ Q16: How can I use CD-ROM under OS/2 ? ------------------------------------------------------------------------------ A: TEAC CD-ROM will work with the embedded ATAPI driver in OS/2 Warp Ver.3.0. ------------------------------------------------------------------------------ Q17: How can I get the device driver for Windows NT/95 ? ------------------------------------------------------------------------------ A: Please select embedded ATAPI driver in Windows NT/95. ============================================================================== Technical support ============================================================================== TEAC America Inc. Phone 213-727-4860 BBS 213-727-7660 Fax on Demand 213-727-7629