This release note and the software that accompanies it are copyright (c) 2004, Intel Corporation, and may only be installed and used in accordance with the license that accompanies the software.

Driver Version = 2.10.9.01
OS supported = RHAS2.1

This download supports Intel(R) SCSI RAID controllers using software stack 2 (the SRCU42X, SRCS16, SRCZCRX, SRCU42E, SROMBU42E, and SRCU41L), please verify that this driver has been tested with the RAID card you have chosen to use by checking the drivers web page for your controller at //Support.Intel.Com.
This package contains the Red Hat Linux AS2.1 driver for the SRCU42X controller.  This driver is not compatible with the SRCU21, SRCU31, SRCU31L, SRCMR, SRCZCR, SRCU32, SRCU42L, or SRCS14L RAID controllers.

Attention!
===========
Extract package contents to a user specified location such as = a:\


Contents
=========
The following files are included in this zip:

Name						DAte		Size		Description
Web License.rtf					06/27/03	13KB		License file
megaraid2-v2.10.9.0-rhas21-kernels.img.gz	08/17/04	256KB		Module list
patches.tar					8/13/04		10KB		Module Dependency
RHAS21_DRV_readme.txt				10/01/04	2KB		This file

Installation Instructions
=========================
1. Extract the contents of the zip to a floppy diskette.
2. Boot to CD-ROM with Disk 1.
3. At the Linux installation prompt type: linux dd
4. When prompted, insert the floppy diskette created in step one.
5. Follow the Red Hat Linux installation procedure to complete the installation.
6. Reboot the system.

Following steps should be used to update the driver

1.	Use "linux noprobe dd" to begin driver update
2.	Select "Yes" when "Do you have a driver disk?" dialog appears
3.	You might see another dialog box if there are more than one possible driver update media, e.g., a usb floppy. Choose appropriate media
4.	Press "Ok" after inserting the update media
5.	IMPORTANT. Following the above step, there would be a dialog  "No driver of appropriate type was found..."
	Select "Manually choose". At the next screen, scroll down the list of all available drivers and select "LSI MegaRAID Driver 2.10.9 (megaraid2)"
	Now driver should install. You can verify by switching to console F4 using "ALT-F4"
6.	If there are no more driver updates, choose "No" when asked "Do you want to load any more driver disks"
7.	Now there would a dialog box confirming the driver update "The following drivers have been found on your system, MegaRAID Driver 2.10.9 (megaraid2)". Select done.
8.	Now, here is the tricky part. If the driver used during installation fails to load with "unresolved symbol" errors when booting subsequently with the UP kernel.  The SMP kernel works ok. To overcome, here is the workaround
	i.	Install normally, and just before hitting the exit button on the last screen of installation, switch to F2 console and do the following steps manually
	ii.	# mkdir /a
	iii.	# mount /dev/fd0 /a	# or appropriate device for update media e.g., /dev/sda
	iv.	# cd /a
	v.	# ./up.sh
	The last step puts the correct driver in the drivers update directory and make new initrd image. Also, if there is an entry found for older megaraid driver in /etc/modules.conf, it is removed as well. It is recommended to go through the up.sh program on the update disk.



Vendor:	Red Hat
Component:	megaraid2-v2.10.9.0-rhas21-kernels.img

Distribution	32-bit Kernels	Architecture / Comments
RH AS 2.1	2.4.9-e.3BOOT	
	2.4.9-e.3	
	2.4.9-e.3smp	
	2.4.9-e.3enterprise	
	2.4.9-e.34BOOT	
	2.4.9-e.34	
	2.4.9-e.34smp	
	2.4.9-e.34enterprise	
	2.4.9-e.40	
	2.4.9-e.40BOOT	
	2.4.9-e.40smp	
	2.4.9-e.40enterprise	

Updates:
========
Added support for 64 bit applications



*Third-party trademarks are the property of their respective owners.