*********************************************************************** * ACCTON TECHNOLOGY CORPORATION * * EN1207F/EN2242 SERIES FAST ETHERNET ADAPTER * * NetWare ODI Driver Installation * * * * Copyright (C) 2001 Accton Technology Corporation * * All rights reserved. * *********************************************************************** Contents of the file: A. File Description B. Driver Installation for NetWare Server 4.11, 5.0 C. Driver Installation for DOS32 D. Driver Installation for Microsoft Windows 3.x E. Driver Installation for Microsoft Windows 95 F. Parameters Description for EN5251.LAN G. Driver Installation for OS/2 Workstation A. File Description -------------------- Filename Description ----------------------------------------------------------------------------- NetWare.TXT This file presents a summary of the contents for NetWare Client32 driver installation. EN5251.LAN 32-bit ODI driver for EN5251 Based adapter. This driver complies with NetWare ODI Server driver SPEC 3.31. EN5251.LDI The driver (EN5251.LAN) installation information file for NetWare Server 5.0(Moab), 4.11, NeDOS32, Microsoft Windows 3.x. EN5251.INF The driver (EN5251.LAN) installation information file for Microsoft Windows 95. B. Driver Installation for NetWare Server 4.11, 5.0 --------------------------------------------------- 1. Change directory to NetWare Server directory (for example: CD\NWSERVER) 2. Load NetWare Server System by typing "SERVER", then press . 3. When the Server prompt appears, load the NetWare Server Installation Utility. That is, :LOAD INSTALL <- If you use NetWare 4.11 :LOAD NWCONFIG <- If you use Netware 5 4. Select "Driver options" from "Installtion Options" menu, then press . 5. Select "Configure network drivers" from "Driver Options" menu, then press . 6. Select "Select a driver" from "Additional Driver Actions" menu, then press . 7. Press to install an unlisted driver, then press to specify a different path. 8. Insert Accton EN5251 Based Fast Ethernet Adapter Driver Diskette to your PC's floppy drive and specify the drive (A: or B:), then press . 9. Select "Accton EN5251 Based Fast Ethernet Adapter(32-Bit ODI)" from "Select a driver to installed:" menu, then press . 10. If necessary, select "Select/Modify driver parameters and protocols" from "Board EN5251_1 (Driver EN5251) Actions" menu, then press to set up the driver parameters. (Please refer to content F.) Otherwise, select "Save parameters and load driver", then press . 11. Following instructions to complete the driver installation. 12. Sample AUTOEXEC.NCF for NetWare Server AUTOEXEC.NCF (one board) ======================== LOAD EN5251 FRAME=ETHERNET_802.2 NAME=E_8022 LOAD EN5251 FRAME=ETHERNET_802.3 NAME=E_8023 LOAD EN5251 FRAME=ETHERNET_II NAME=E_II LOAD EN5251 FRAME=ETHERNET_SNAP NAME=E_SNAP BIND IPX E_8022 NET=10 BIND IPX E_8023 NET=20 BIND IPX E_II NET=30 BIND IPX E_SNAP NET=40 AUTOEXEC.NCF (two boards) ========================= LOAD EN5251 SLOT=10001 FRAME=ETHERNET_802.2 NAME=E_8022_1 LOAD EN5251 SLOT=10001 FRAME=ETHERNET_802.3 NAME=E_8023_1 LOAD EN5251 SLOT=10001 FRAME=ETHERNET_II NAME=E_II_1 LOAD EN5251 SLOT=10001 FRAME=ETHERNET_SNAP NAME=E_SNAP_1 LOAD EN5251 SLOT=10002 FRAME=ETHERNET_802.2 NAME=E_8022_2 LOAD EN5251 SLOT=10002 FRAME=ETHERNET_802.3 NAME=E_8023_2 LOAD EN5251 SLOT=10002 FRAME=ETHERNET_II NAME=E_II_2 LOAD EN5251 SLOT=10002 FRAME=ETHERNET_SNAP NAME=E_SNAP_2 BIND IPX E_8022_1 NET=10 BIND IPX E_8023_1 NET=20 BIND IPX E_II_1 NET=30 BIND IPX E_SNAP_1 NET=40 BIND IPX E_8022_2 NET=50 BIND IPX E_8023_2 NET=60 BIND IPX E_II_2 NET=70 BIND IPX E_SNAP_2 NET=80 C. Driver Installation for DOS32 -------------------------------- 1. If you have completed installation the NetWare Client 32 for DOS, all you have to modify STARTNET.BAT. Please see the sample STARTNET.BAT below these installation instructions. 2. In DOS environment, run "INSTALL" from Netware 4.11 CD root directory. Follow the installation steps of Novell NetWare Client 32. - When "Select the type of installation desired" window appears, select "Client Installation". - When "Select Client to be installed" window appears, select "NetWare Client 32 for DOS and Windows 3.1x" - When the product manual appears, mark the "Netware Client 32 for DOS" item, then press . - When the "Select a LAN Driver Type" windows appears, select "32-bit LAN Drivers", then press . 3. In "32-Bit Network Board Drivers" window, select "USER SPECIFIED 32 BIT DRIVER", then press . 4. Insert Accton EN5251 Based Fast Ethernet Driver Diskette into your floppy diskette drive, then specify the driver path like A:\LANDRV32, then press . 5. Select "Accton EN5251 Based Fast Ethernet Adapter(32-Bit ODI)", then press . 6. Refer to Content F) and set the correct driver parameters to comply with your network environment, then press to continue. 7. Following instructions to complete the Client32 for DOS software installation. 8. Reboot your machine. Sample STARTNET.BAT for DOS32. ============================== SET NWLANGUAGE=ENGLISH C:\NOVELL\CLIENT32\NIOS.EXE LOAD C:\NOVELL\CLIENT32\LSLC32.NLM LOAD C:\NOVELL\CLIENT32\CMSM.NLM LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM LOAD C:\NOVELL\CLIENT32\EN5251.LAN FRAME=ETHERNET_802.2 LOAD C:\NOVELL\CLIENT32\EN5251.LAN FRAME=ETHERNET_802.3 LOAD C:\NOVELL\CLIENT32\EN5251.LAN FRAME=ETHERNET_II LOAD C:\NOVELL\CLIENT32\EN5251.LAN FRAME=ETHERNET_SNAP LOAD C:\NOVELL\CLIENT32\IPX.NLM LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM D. Driver Installation for Microsoft Windows 3.x ------------------------------------------------- Please refer to Content C), in step 2, mark "Netware Client 32 for DOS" and "NetWare Client 32 for Windows", then following step 3..8 to complete the installation. E. Driver Installation for Microsoft Windows 95 ----------------------------------------------- If you have installed the Microsoft Client in your Windows 95 system, you should remove the adapter object and NDIS3 driver of the EN5251 Based Adapter from the Windows 95 system and delete C:\WINDOWS\INF\EN5251.INF file. Install Novell NetWare Client 32 for Windows 95 =============================================== 1. Plug EN5251 Based adapter into one of the Master PCI slots of your PC. 2. Turn the PC power ON and then boot from Windows 95. 3. Windows 95 will prompt "PCI Ethernet Controller" in "New Hardware Found" dialog box. Please click on "Cancel" and do not install driver now. 4. In WIN95 environment, run "SETUP.EXE" in the \PRODUCTS\WIN95\IBM_ENU directory of Netware 4.11 CD. Follow the installation steps of Novell NetWare Client 32. 5. In "Select Device" window, please select "[detected net drivers]" and click on "OK" button to follow the installation steps of Client 32. (Please do not click "Have Disk..." to install adapter driver now.) 6. After following the instructions to complete the Client32 for WIN95 software installation, reboot your machine. Install Driver After Novell NetWare Client 32 for Windows 95 is Installed ========================================================================= 1. Make sure Novell NetWare Client 32 is installed OK and then install EN5251 based adapter driver again. When the PC is powered on, Windows 95 will prompt "PCI Ethernet Controller" in "New Hardware Found" dialog box. (If your adapter is not detected by Windows 95, refer to TroubleShooting below.) 2. Remove the Accton EN5251 Based Fast Ethernet Adapter Driver Diskette in your floppy drive. Click on "Next" button and do not let WIN95 search adapter driver. 3. Insert the Accton EN5251 Based Fast Ethernet Adapter Driver Diskette in your floppy drive. Click "Other Locations" and type "A:\LANDRV32", then click "OK" button. The message "Accton EN5251 Based Fast Ethernet Adapte for Novell Netware Client 32" will appear. 4. After the "Finish" button is clicked, Windows starts to copy files from Windows 95 CD-ROM to your hard disk. When the "Copying Files" dialogue shows up to request the directory for the "EN5251.LAN" file, type "A:\LANDRV32" and click on the "OK" button. 5. Follow the screen's prompt to insert "NetWare Client 32 for Windows 95" disk and click the OK button in the "Insert Disk" dialog box. 6. Otherwise enter the full pathname (ex. D:\PRODUCTS\WIN95\IBM_ENU) of the "NetWare Client 32 for Windows95" installation files in the "Copying Files....." dialog box, then click the OK button. 7. Follow the screen's prompt to insert the "Windows 95 CD-ROM" and click the OK button in the "Insert Disk" dialog box. 8. Otherwise enter the full pathname of the "Windows 95 CD-ROM" installation files in the "Copying Files..." dialog box, then click the OK button. 9. Windows 95 will copy the driver (EN5251.LAN) from A:\LANDRV32 to C:\NOVELL\CLIENT32 directory. 10. Remove the Accton EN5251 Based Fast Ethernet Adapter Driver Diskette from your floppy drive. 11. Restart your computer to initialize the network function. ** NOTE ** - C:\NOVELL is the directory where your Novell Client 32 files are located. - C:\WINDOWS is the directory where your Windows 95 O.S. is located. - Do not remove "Novell ODINSUP" from the Network control panel. Removing Novell ODINSUP also removes NetWare Client 32 for Windows 95 if there is only one adapter in use. TroubleShooting in Windows 95 ============================= If your adapter is not detected by Windows 95 "New Hardware Found", your adapter may be already REGISTERED. Therefore, you have to remove the REGISTERED before you install adapter driver again. Method: 1. Click "Network" icon in the "Control Panel" box to make sure your adapter driver not installed. If your adapter driver was installed, remove it. 2. Select "Start" button (left-down corner) and select "Run" item. Type REGEDIT, the registry edidor utility , then click "OK" button to execute it. 3. In the Registry Editor dialogue, double-click "HKEY_LOCAL_MACHINE" item, double-click "Enum", then double-click PCI item. Select the "VEN_1216&DEV_1113", then delete it. Close Register Editor dialogue. 4. Reboot Windows 95 again to carefully follow the installtion procedures above again. F. Parameter Description for EN5251.LAN ---------------------------------------- The following parameters are used in EN5251.LAN. 1. SLOT: specifies which adapter is enabled when multiple EN5251 based adapters are found in your computer. Ex: LOAD EN5251 SLOT=1 FRAME=ETHERNET_802.2 LOAD EN5251 SLOT=1 FRAME=ETHERNET_II 2. FRAME: specifies which frame type is used by the driver. Accepted values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and Ethernet_SNAP. Multiple frame types can be enabled by the driver by loading the same driver with different FRAME types. Ex: LOAD EN5251 FRAME=ETHERNET_802.2 LOAD EN5251 FRAME=ETHERNET_802.3 LOAD EN5251 FRAME=ETHERNET_II LOAD EN5251 FRAME=ETHERNET_SNAP 3. NODE: Use a different address to replace the node address burned in EEPROM. Ex: LOAD EN5251 NODE=0200E8001122 4. There are five parameters provided for specifying adapter's speed and duplex mode : AUTO, 10-HD, 10-FD, 100-HD, 100-FD. Ex: LOAD EN5251 100-HD FRAME=Ethernet_802.2 NAME=LAN_A BIND IPX TO LAN_A NET=11 ** All trademarks and brand names mentioned belong to their respective owners. G. NetWare OS/2 ODI Workstation Driver Installation --------------------------------------------------- This section describes the procedure to install the NetWare OS/2 ODI workstation driver for your adapter. You can use the following methods to install the driver. G.1 Install method ================== Requirements ------------ Accton EN5251 Based Fast Ethernet Adapter Driver Diskette (EN5251.SYS) Driver Location: \NetWare\OS2ODI Installation Procedure ---------------------- 1. Run INSTALL utility for Netware OS/2 requester and follow its instructions. 2. Assign EN5251.SYS as the network interface driver name and specify the path as A:\NETWARE\OS2ODI. 3. Insert Accton EN5251 Based Fast Ethernet Adapter Driver Diskette into driver A. then wait for file copy completion. 4. Choose the session support you need. For more information, please see Netware OS/2 Requester Manual. 5. Save configuration. 6. Run CONFIGURATION UTILITY and select "THIS WORKSTATION" to modify the NET.CFG file. (This file is located in the root directoy of OS/2 system, you can use any text editor to modify it.) 7. Shutdown and restart the machine. ** NOTE ** If your OS/2 version is 2.0 or later, you must have the Netware OS/2 Requester version 2.01 or later. G.2 Manual method ================= PREREQUISITES: You will need the following diskettes: Accton EN5251 Based Fast Ethernet Adapter Driver Diskette (EN5251.SYS) Driver Location: \NetWare\OS2ODI Novell NetWare OS/2 WORKSTATION SERVICES REQUESTER diskette Novell NetWare OS/2 WORKSTATION OS/2 Utility - 1 Novell NetWare OS/2 WORKSTATION OS/2 Utility - 2 Novell NetWare OS/2 WORKSTATION OS/2 Utility - 3 2. Make sure that the computer is at least a 286 or 386 machine that will run OS/2 or Extended Edition OS/2. 3. Install the OS/2 Requester, referring to Novell's documentation for NetWare Requester for OS/2 installation. 4. Copy the \NetWare\OS2ODI\EN5251.SYS file from the support disk into the NETWARE subdirectory on your hard disk. 5. Add or replace the EN5251.SYS command line in the CONFIG.SYS file. Make sure it precedes the IPX.SYS command line. An example: DEVICE=C:\NETWARE\LSL.SYS ; OS/2 Requester supported DEVICE=C:\NETWARE\DDAEMON.SYS ; OS/2 Requester supported DEVICE=C:\NETWARE\EN5251.SYS ; Accton supported DEVICE=C:\NETWARE\IPX.SYS ; OS/2 Requester supported 6. Reboot the computer and log onto your network. ** INSTALLATION NOTE ** ----------------------- You can bind several frame types to the IPX protocol to support various configurations -- in the Link Driver EN5251 section of the NET.CFG file. SAMPLE: Link Driver EN5251 frame Ethernet_802.2 frame Ethernet_802.3 frame Ethernet_II frame Ethernet_snap protocol IPX 00 Ethernet_802.3