Copyright: Copyright (c) Olicom AS 1993-97.


0016: The Memory Window could not be accessed for driver. Check that no other devices uses the 4K region reserved to access the
16  The Memory Window could not be accessed. Check that no other devices uses the 4K region reserved to access the PC Card CIS through the Memory Window parameter

The driver needs a 4K region through which the CIS can be accessed during PC Card detection and initialization. The starting address of this 4K region is specified by the Memory Window parameter.

The driver was unable to reserve the 4K region of memory because it is already in use by another device in the system.

Action: Change the Memory Window parameter to a different value to try using another memory region.


0017: The interrupt specified for the driver PCMCIA card is not supported by the PCMCIA controller found in the system
17  The interrupt specified for the driver PC Card card is not supported by the PC Card controller found in the system

The interrupt specified in the PC Card settings is not supported by the PC Card controller in the system.

Action: Change the interrupt to a value supported by the PC Card controller.


0018: There where no PCMCIA windows available to retrieve the CIS for driver
18  There where no PC Card windows available to retrieve the CIS

The DataBook PC Card controller had no free PC Card Memory Windows to access the CIS.

Action: Remove unneeded PC Card devices and reboot the system. If the error persists, contact your place of purchase.


0019 The node address found on the PCMCIA card for driver is invalid. Check that the memory window is not used by other devices
19  The node address found on the PC Card for driver is invalid.

The node address read from the PC Card is invalid, i.e. it has either wrong length or it is an invalid node address.

Action: Check that the 4K memory region starting at the address specified by the Memory Window parameter is not in use by other devices. Try using a different memory region by changing the Memory Window parameter. If the error persists, run diagnostics on the PC Card to verify that a correct node address is stored on the PC Card.


0020: An error occured while testing the PCMCIA Card found by %2. Check for I/O port conflicts with other adapters in the syste
20  An error occurred while testing the PC Card found

The driver has found a PC Card in the system, but was unable to access the card correctly.

Action: Check for I/O port conflicts with other adapters in the system. Try changing the Data Size parameter and adding Additional Waitstates for the adapter.


0021: The number of receive buffers allocated for driver cannot handle the maximum frame size specified. Maximum frame size has
21  The number of receive buffers allocated cannot handle the maximum frame size specified. Maximum frame size has been modified

The specified maximum frame size cannot be set due to limitations on the receive area allocated. Each receive buffer is 2048 bytes long, so the maximum frame size will be adjusted to 2048 * the number of receive buffers allocated.

Action: Increase the number of receive buffers for driver or decrease the maximum frame size for the driver.


5000
5000 driver : Has encountered a conflict in resources and could not load.

The resources needed for your network adapter conflicts with another adapter.

Action: Check the resources used by the network adapter(s) to ensure that no conflicts exists.


5001
5001 driver : Could not allocate resources necessary for operation.

The network adapter driver failed to load, because it tried to allocate too many resources.

Action: Decrease the number of receive and/or transmit buffers and retry.


5002
5002 driver : Has determined that the adapter is not functioning properly.

The adapter could not be found or is not working properly.

Action: Check I/O base settings and retry.


5003
5003 driver : Could not find an adapter.

The adapter could not be found by the network adapter driver.

Action: Check I/O base settings and retry.


5004
5004 driver : Could not connect to the interrupt number supplied.

The interrupt is already used by another device.

Action: Change the adapter interrupt number and retry.


5005
5005 driver : Has encountered an internal error and has failed.

An internal error has been discovered.

Action: Restart your system. If the error persists, contact your place of purchase for support.


5006
5006 driver : The version number is incorrect for this driver.

The network adapter driver version is incorrect.

Action: Restart your system. If the error persists, contact your place of purchase for support.


5007
5007 driver : Timed out during an operation.

A time-out error occurred.

Action: Restart your system. If the error persists, contact your place of purchase for support.


5008
5008 driver : Has encountered an invalid network address.

An invalid network address was specified.

Action: Change the locally administered network address and restart your system. If the error persists, try clearing the network address in the setup dialog. The network adapter driver will then use the burned-in address when opening.


5009
5009 driver : Does not support the configuration supplied.

An invalid configuration entry was discovered.

Action: Use the network control panel to set proper adapter parameters. Do not try to manually change any parameters in the registry.


5010
5010 driver : The adapter has returned an invalid value to the driver.

An internal error has occurred.

Action: Restart your system. If the error persists, contact your place of purchase for support.


5011
5011 driver : A required parameter is missing from the registry.

A parameter necessary for operation has been omitted in the registry.

Action: Use the network control panel to set proper parameters.


5012
5012  driver : The IO Base Address supplied does not match the jumpers on the adapter.

The adapter could not be found by the network adapter driver.

Action: Check I/O base settings and retry.


5014
5014 driver : The adapter is disabled. The driver cannot open the adapter.

The adapter is disabled.

Action: Make sure the start-up parameter for the network adapter driver is set to "Manual". Use the "Devices" applet in the control panel to change the settings.


5015
5015 driver : There is an I/O port conflict.

The ports used by the network adapter driver are already in use by another device.

Action: Change the I/O Base address for the adapter.


5016
5016 driver : There is an I/O port or DMA channel conflict.

The ports or DMA channel used by the NDIS 3 driver are already in use by another device.

Action: Check the I/O port and DMA usage by the adapter to ensure that there is no resource conflicts.


5017 driver: There is a memory conflict at address xxxxxxxx

The Memory Window used for accessing the PC Card's CIS is in use by another device in the system.

Action: Change the Memory Window parameter to a 4K region that is not being used by other devices in the system.


5018
5018 driver : There is a interrupt conflict at interrupt number xx.

The adapter tried to use an interrupt currently in use.

Action: Change the interrupt selection on the adapter and retry.


5019
5019 driver : There is a resource conflict at DMA channel xx.

The adapter tried to use a DMA channel currently in use.

Action: Change the DMA channel selection on the adapter and retry.


AST PowerExec 3/25SL

Do not configure your PC Card to use interrupt level 7.


Adapter check
3  The network adapter generated an Adapter Check error

A serious error occurred on the adapter, causing an adapter check code to be posted.

Action: Restart your system. If the error persists, contact your place of purchase for support.


Adapter disabled due to multiple severe warnings
25  Adapter disabled due to multiple severe warnings

The adapter was disabled because several non-fatal errors occurred. Look at the preceding warning messages in the Event Log to determine the source of the problem.


Adapter failed to open because it was the first station
29  Adapter failed to open because it was the first station to insert to the ring.

If the adapter is the first station to insert to an empty token ring it will not be able to auto sense the ring speed. You can prevent this problem by selecting a fixed ring speed in the Network Control Panel. Normally you would force the speed setting for stations acting as servers to let these stations determine ring speed for workstations that are usually shut down during non-working hours. In a switched network you should never see this error message.


Adapter not supported
13  The detected network adapter is not supported by this driver

You have installed the wrong network adapter driver for the adapter or your adapter is not supported.

Action: Get the newest network adapter driver available for your network adapter.


Adapter removed from ring
12  The network adapter has received a remove ring station Mac frame request and has deinserted from the ring

The adapter has been removed by a LAN Manager station.

Action: Contact your network administrator.


Additional Waitstates

This parameter is used for setting the hardware waitstates on I/O to the PC Card.

The default value is 0.

Change this parameter only if the network driver reports errors.

The actual number of wait states depends on the PC Card controller in the computer.


Auto disabled
15  The network adapter has received a Trace Tool Remove frame from a Network Management station and has disabled the promiscuous packet filter

The network adapter driver has cleared the PROMISCUOUS packet filter bit, as instructed by a LAN Manager station.

Action: Contact your network administrator.


Bring-up diagnostic error
1  Bring-up diagnostics failed

The adapter failed during the bring-up diagnostics.

Action: Shut down your system and retry the operation. If the error persists, contact your place of purchase for support.


Bus Type

The Bus Type parameter is used when the system has several types of busses, e.g. ISA/PCI, EISA/PCI etc. Choose the bus type for the adapter you are installing.


Bus number

Use the Bus Number parameter only when the network adapter is installed in a PC with multiple identical busses, e.g. if you are installing a PCI adapter in a system with a PCI-bridge.If the adapter is not inserted in the primary PCI bus, i.e. it is accessed across a PCI-bridge, the Bus Number parameter may need to be changed to another value.

If the PC only has a single bus, set this parameter to 0. This is the usual situation and applies to ISA/PCI, EISA/PCI busses as well.


Cable connection
10  Lobe wire fault detected. Please check cable connections

The connection to the network has been removed.

Action: Check all cables and connections and try another lobe media cable. The adapter continues to try to reinsert on the ring.


Chicony SubNote 486

This notebook uses the TCIC-2/N PC Card controller.


COM1

Communication port 1 is located at I/O address 0x3F8.

In Windows NT and Windows 95, the network adapter and the modem is sharing the PC Card interrupt selected.


COM2

Communication port 2 is located at I/O address 0x2F8.

In Windows NT and Windows 95, the network adapter and the modem is sharing the PC Card interrupt selected.


COM3

Communication port 3 is located at I/O address 0x3E8.

In Windows NT and Windows 95, the network adapter and the modem is sharing the PC Card interrupt selected.


COM4

Communication port 4 is located at I/O address 0x2E8.

In Windows NT and Windows 95, the network adapter and the modem is sharing the PC Card interrupt selected.


COM5

Communication port 5 is located at the I/O address with offset 0x18 from the I/O Base Address and only available if running Windows NT using the built-in PC Card enabler.

In Windows NT and Windows 95, the network adapter and the modem is sharing the PC Card interrupt selected.


Communication Port

Selects a COM port to use or disables the modem functionality. Choose:

Com1

Com2

Com3

Com4

Com5

Disabled

If Disabled is selected, no communication port will be available on the LAN/Modem PC Card.

Notice that if you have installed more than one LAN/Modem PC Card you can only enable the COM port on one card at a time.


Compaq Concerto

Do not configure your PC Card to use interrupt level 9.


Configuration
14  The configuration read from the network adapter is invalid

A configuration entry is invalid.

Action: Use the network control panel to set-up proper adapter settings.


Conflicts with other devices

When installing a PC Card there is a possible conflict when selecting I/O ports, Interrupt level and Memory Window for accessing the information stored on the PC Card. If a conflict exists, you may get an error when the driver is loaded.

If you are using Microsoft Windows NT 3.5, use the Windows NT Diagnostics program WINMSD.EXE to find a vacant value for the resources needed:

1.	Select File|Run... from the Program Manager.

2.	Enter "WINMSD.EXE" and press Enter.

3.	Select "IRQ/Port Status..."

4.	In the list of used Interrupts, find a number, that is not used by any other devices. The interrupt must be supported by the PC Card controller in the system

5.	In the list of used Ports, find a free 0x20-byte (32 bytes) region starting at a 0x10 byte boundary, i.e. 0x210-0x230 or 0x340-0x360.

6.	Select "OK".

7.	Select "DMA/Memory..."

8.	In the list of used Memory, find a free 4K region, that is not in use by any other devices in the system. The region must be 4K aligned, i.e. end with 3 zeros, e.g. 0xD0000, 0xD7000 and be in the range 0xA0000-0xFF000

9.	Select "OK".

10.	Exit the Windows NT Diagnostics program.

The found values can now be used when configuring the network card in the PC Card settings dialog box.


Contents
Contents for Network Installation help

The Microsoft® Windows NT™ and Windows 95/98 operating systems uses NDIS 3 network drivers.

This help file explain the configuration parameters for the network driver you are installing or configuring. You must be logged on as a member of the Administrators group in order to be able to install and configure network adapters.

Use this help file as a guide if you experience any problems with your network adapter. It contains a list of all network adapter driver error messages and proposed actions.

This help file is also accessible as a separate help file OCT3X.HLP.


Could not open network adapter. Insert denied
24  Could not open network adapter. Insert denied

The network adapter was unable to attach to the network. Contact your network administrator.


Could not open network adapter. Speed sense failed
23  Could not open network adapter. Speed sense failed

Try restarting your system. If the error persists you should force the ring speed to a fixed value.


Datasize

This parameter is used for setting the I/O data path size to the PC Card.

The default value is 16 bit.

Change this parameter only if the network driver reports errors.


Download failed
9  Could not download code on adapter

The download operation failed.

Action: Restart your system. If the error persists, contact your place of purchase for support.


Duplicate node address
5  Could not open adapter. Duplicate node address.

A duplicate address has been discovered on the ring.

Action: Change your locally-administered address as discussed in the Adapter parameters section and restart your system.


EarlyToken
Early Token Release

Specifies whether Early Token release should be used or not.

This parameter is only applicable when running at 16 Mb/s.


Errors
Error descriptions

If you observe any problems with the network, you should check if any error messages or warnings are posted by the network adapter driver by using the Event Viewer in the Administrative Tools group.

All error messages and/or warnings posted by the network adapter driver have the Source field set to "Oct3xnd?" where ? is either 3, 4 or 5.

System error messages related to the network adapter driver can occur with different source names, i.e. "Service Control Manager".

The messages are enumerated by the Event field and are described below in Event number order. In the event viewer display the message description by highlighting the message and pressing the enter key. Error messages from 5000 are predefined error codes specific to the Windows NT™ operating system. You can retrieve additional information on these messages in your documentation.

NOTE: If you are running Windows 95 or Windows 98, errorcodes are found in hexadecimal format in the NDISLOG.TXT file in the Windows directory.

1: Bring-up diagnostics failed

2: Adapter initialization failed

3: The network adapter generated an Adapter Check error

4: Could not open adapter. Ring beaconing. Check network speed settings

5: Could not open adapter. Duplicate node address

6: Could not open adapter. Request initialization failed

7: Could not open adapter. Remove station received

8: Could not open adapter

9: Could not download code on adapter

10: Lobe wire fault detected by. Please check cable connections

11: The network adapter has failed the lobe wrap test resulting from the beacon auto-removal process and has deinserted from the ring

12: The network adapter has received a remove ring station Mac frame request and has deinserted from the ring

13: The detected network adapter is not supported by this driver

14: The configuration read from the network adapter is invalid

15: The network adapter has received a Trace Tool Remove frame from a Network Management station and has disabled the promiscuous packet filter

16: The Memory Window could not be accessed. Check that no other devices uses the 4K region reserved to access the PC Card CIS through the Memory Window parameter

17: The interrupt specified for the PC Card is not supported by the PC Card controller found in the system

18: There where no PC Card windows available to retrieve the CIS

19 The node address found on the PC Card is invalid.

20: An error occurred while testing the PC Card found

21: The number of receive buffers allocated cannot handle the maximum frame size specified. Maximum frame size has been modified.

23: Could not open network adapter. Speed sense failed

24: Could not open network adapter. Insert denied

25: Adapter disabled due to multiple severe warnings

29: Adapter failed to open because it was the first station to insert to the ring

5000: driver : Has encountered a conflict in resources and could not load

5001: driver : Could not allocate resources necessary for the operation

5002: driver : Has determined that the adapter is not functioning properly

5003: driver : Could not find an adapter

5004: driver : Could not connect to the interrupt number supplied

5005: driver : Has encountered an internal error and has failed

5006: driver : The version number is incorrect for this driver

5007: driver : Timed out during an operation

5008: driver : Has encountered an invalid network address

5009: driver : Does not support the configuration supplied

5010: driver : The adapter has returned an invalid value to the driver

5011: driver : A required parameter is missing from the registry

5012: driver : The IO Base Address supplied does not match the jumpers on the adapter

5014: driver : The adapter is disabled. The driver cannot open the adapter

5015: driver : There is an I/O port conflict

5016: driver : There is an I/O port or DMA channel conflict

5017: driver : There is a memory conflict at address xxxxxxxx

5018: driver : There is a interrupt conflict at interrupt number xx

5019: driver : There is a resource conflict at DMA channel xx


FullXmitStat
Full Transmit Status

When set to "Yes", normal transmit verification is performed, and the upper layer protocols will be notified about the status of the transmitted frame, i.e. whether the destination address has been recognized and the frame has been copied by the receiving station. When this value is "No", all transmitted frames are assumed both recognized and copied by another station on the ring. If you have a bridge/router in your network or discover abnormal network behavior, set this value to "Yes".


IBM PS/2 ThinkPad 755 CD

2 additional hardware wait states on the PC Card bus are needed on this device.


IBM PS/2E 9533

2 additional hardware wait states on the PC Card bus are needed on this device.


IBM Port Replicator 1

The PC Card Controller I/O Base parameter in the Advanced PC Card section must be specified to 3E2 by selecting "Driver enabler (3E2h)".


IBM ThinkPad 360 CSE

2 additional hardware wait states on the PC Card bus are needed on this device.


Initialization error
2  Adapter initialization failed

The adapter failed the initialization phase.

Action: Shut down your system and retry the operation. If the error persists, contact your place of purchase for support.


Interrupt

This parameter specifies the interrupt level used by the PC Card.

For notebooks using the TCIC-2/N PC Card controller the interrupt level must not be set to any of the values 9, 11 or 15, as these levels are not supported by the TCIC-2/N PC Card (DB86082) controller.


IoBaseAddress
I/O Base address

The I/O base address specifies where the network adapters I/O ports are located. Only the specified I/O range is scanned for an adapter. If an invalid I/O address range is selected, you will be unable to connect to the network.

Select Auto Detect to search for an adapter at all supported I/O addresses. You can use this option, even if you have installed multiple Token-Ring adapters in your system.

If the adapter cannot be found at the specified I/O address, the Cannot find adapter error message is posted.

This parameter is not available for PCI adapters and PC Cards.

For PC Cards, see PC Card I/O base settings for more details.


MaxFrameSize
Maximum Frame Size

Specifies the maximum frame size the network adapter driver can handle. This parameter is also used for allocating internal memory for handling frames in special situations.

However, system resources are limited and you may have problems loading the network adapter driver if it allocates large amounts of data. Allocating too many resources will result in a resource error.


Memory Window

During initialization of the PC Card controller, the driver needs a 4 kByte memory window. This parameter specifies the location of the memory window.


NDIS

Network Driver Interface Specification


NetAddress
Network address

Use the Network address field if you do not want to use the network adapter's burned in Token Ring address. The value entered must be a locally administered address, i.e. in the range from 400000000000 to 7FFFFFFFFFFF. The value can be entered as "XX-XX-XX-XX-XX-XX" for improved readability.

If the network adapter driver encounters an invalid network address, the invalid network address error message is posted.

The value entered is verified by the setup program when you click "Ok" in the setup dialog box.


Open error
8  Could not open adapter

The adapter failed to open.

Action: Check cables and connections and retry. If the error persists, try a different lobe media cable.


PCIC or compatible (e.g. Intel)

The PCIC (Intel 82365SL compatible) PC Card controller supports interrupt levels 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.


PCMCIA Advanced Settings
PC Card Advanced Settings

The parameters in this section only needs to be changed if you experience driver initialization errors even if there are no resource conflicts. The following parameters are changeable:

PC Card Enabler

Additional Waitstates

Datasize

If you experience any problems, check if there is any known problems with your notebook.


PCMCIA I/O Base Address
PC Card I/O Base Address

The I/O base address specifies where the PC Card's I/O ports should be located. The specified I/O range is used to instruct the PC Card card enabler where to enable the card in the I/O range. If an I/O address range is selected, which is already in use, you will be unable to connect to the network because of a resource conflict.

The card will use 32 I/O ports starting at the address specified.

If the adapter cannot be found at the specified I/O address, the Could not find an adapter error message is posted. Check for resource conflicts.


PCMCIA Setup_1
PC Card Settings

If you are using a PC Card, the network driver needs additional information for setting up the PC Card controller and PC Card in your PC. Usually the default PC Card parameters will work, but all parameters should be checked for conflicts with other devices.

The following PC Card parameters must be set:

PC Card I/O Base Address

Memory Window

Interrupt

Ring Speed

If you are installing a LAN/Modem adapter, you need to specify a

Communication Port

Some PCs require additional hardware dependent settings in order to work properly. These parameters are changed using the PC Card Advanced Settings. If you need to disable the PC Card facility, this is done in the advanced settings as well.

PC Card controllers supported are:

PCIC or compatible (e.g. Intel).

TCIC or compatible (e.g. Databook).


Parameters
Parameter descriptions

The following parameters are applicable for the network adapter driver:

I/O Base Address

Receive Buffers

Transmit Buffers

Max Frame Size

Early Token Release

Full Transmit Status

Network address

Ring Speed

Wake-on-LAN

All parameters have a default value suitable in most situations. However, if you need to install several adapters in your system or use locally-administered addresses, you may need to change some of them.

If you are installing drivers for a PC Card, you will need to specify some additional PC Card settings.


Pcmcia Enabler
PC Card Enabler

The PC Card Enabler allocates resources to PC Cards. You can choose to use the Windows NT built-in PC Card Enabler or you can use the PC Card Enabler built into the network adapter driver. The driver built-in PC Card Enabler supports a wider range of PC Card controllers and MUST be used if your PC Card has modem capabilities and you are running on Windows NT 3.51.

In certain notebook configurations it is required to define a special I/O base address for the PC Card controller. An example is the IBM Port Replicator 1 used with an IBM Thinkpad notebook. In this case the PC Card controller I/O Base must be set to 3E2h

Default PC Card controller I/O Base is 3E0h for PCIC compatible controllers and 240h for TCIC compatible controllers.


Receive buffers

This parameter specifies the number of receive buffers allocated by the network adapter driver. Allocating a large number of receive buffers prevent the adapter from congesting when receiving large amounts of data.

However, system resources are limited and you may have problems loading the network adapter driver if it allocates large amounts of data. Allocating too many resources will result in a resource error.


Remove station received
7  Could not open adapter. Remove station received

The adapter has been removed by a LAN Manager station.

Action: Contact your network administrator.


Request initialization error
6  Could not open adapter. Request initialization failed

An error occurred during adapter initialization.

Action: Restart your system. If the error persists, contact your place of purchase for support.


Ring speed

It is possible to force usage of a ring speed of either 4 or 16 Mbps or (for certain adapters) to use the value stored on the adapter. Newer adapter types are able to automatically detect the ring speed and the Ring Speed parameter should then be left in Auto Detect mode unless the network adapter is installed in a server system.

If a wrong ring speed is selected, an error will occur indicating that the selected ring speed is incorrect.


Ring beaconing
4  Could not open adapter. Ring beaconing. Check network speed settings.

The network speed settings on your network adapter probably do not match the ring-speed  used on your token-ring network.

Action: Change your network speed settings and restart your system.


Ring beaconing_1
11  The network adapter has failed the lobe wrap test resulting from the beacon auto-removal process and has deinserted from the ring

The adapter has deinserted from the ring, because the ring was beaconing.

Action: Check the network speed settings and cable connections and retry. If the error persists, contact your network administrator.


Support
Contacting support

If you have any problems, write down the Event ID, Source, Description and Data fields in the Event Detail window. This information helps the support team to locate the error.


TCIC-2/N PCMCIA controller
TCIC-2/N PC Card controller

The Interrupt level must not be set to any of the following values: 9, 11 or 15, as these levels are not supported by the TCIC-2/N (DB86082) PC Card controller.


Transmit buffers

This parameter specifies the number of transmit buffers allocated by the network adapter driver. Allocating a large number of transmit buffers will speed up data transmission.

However, system resources are limited and you may have problems loading the network adapter driver if it allocates large amounts of data. Allocating too many resources will result in a resource error.


Twinhead SubNote 486SLC

This notebook uses the TCIC-2/N PC Card controller

The PC Card memory window should be set to d0000 or d8000.

2 additional hardware waitstates on the PC Card bus are needed on this device.


Wake-on-LAN

If your system supports Wake-on-LAN, this parameter lets the adapter remain open and attached to the network when you shut down Windows. It is now possible to wake the system remotely by sending a Magic Packet™ addressed to your network adapter. This may be convenient for system managment purposes.


Windows 95/98 error codes

If you are running Windows 95 or Windows 98, errorcodes are found in hexadecimal format in the NDISLOG.TXT file in the Windows directory.

The following list will explain the meaning of each possible hexadecimal errorcode:

0xE0000001:	Bring-up diagnostics failed

0xE0000002	Adapter initialization failed

0xE0000003	The network adapter generated an Adapter Check error

0xA0000004	Could not open adapter. Ring beaconing. Check network speed settings

0xE0000005	Could not open adapter. Duplicate node address

0xE0000006	Could not open adapter. Request initialization failed

0xE0000007	Could not open adapter. Remove station received

0xA0000008	Could not open adapter

0xE0000009	Could not download code on adapter

0xA000000A	Lobe wire fault detected by. Please check cable connections

0xE000000B	The network adapter has failed the lobe wrap test resulting from the beacon auto-removal process

0xE000000C	he network adapter has received a remove ring station Mac frame request

0xE000000D	The detected network adapter is not supported by this driver

0xE000000E	The configuration read from the network adapter is invalid

0xA000000F	The network adapter has received a Trace Tool Remove frame

0xE0000010	The Memory Window could not be accessed.

0xE0000011	The interrupt specified for the PC Card is not supported

0xE0000012	There where no PC Card windows available to retrieve the CIS

0xE0000013	The node address found on the PC Card is invalid.

0xE0000014	An error occurred while testing the PC Card found

0xE0000015	The number of receive buffers allocated is too small.

0xA0000017	Could not open network adapter. Speed sense failed

0xE0000018	Could not open network adapter. Insert denied

0xE0000019	Adapter disabled due to multiple severe warnings

0xA000001D	Adapter failed to open because it was the first station to insert to the ring

0xC0001388	driver : Has encountered a conflict in resources and could not load

0xC0001389	driver : Could not allocate resources necessary for the operation

0xC000138A	driver : Has determined that the adapter is not functioning properly

0xC000138B	driver : Could not find an adapter

0xC000138C	driver : Could not connect to the interrupt number supplied

0xC000138D	driver : Has encountered an internal error and has failed

0xC000138E	driver : The version number is incorrect for this driver

0xC000138F	driver : Timed out during an operation

0xC0001390	driver : Has encountered an invalid network address

0xC0001391	driver : Does not support the configuration supplied

0xC0001392	driver : The adapter has returned an invalid value to the driver

0xC0001393	driver : A required parameter is missing from the registry

0xC0001394	driver : The IO Base Address supplied does not match the jumpers on the adapter

0xC0001396	driver : The adapter is disabled. The driver cannot open the adapter

0xC0001397	driver : There is an I/O port conflict

0xC0001398	driver : There is an I/O port or DMA channel conflict

0xC0001399	driver : There is a memory conflict at address xxxxxxxx

0xC000139A	driver : There is a interrupt conflict at interrupt number xx

0xC000139B	driver : There is a resource conflict at DMA channel xx


notebook
Known problems with notebook computers

This note contains installation instructions for specific brands and models of notebooks. If your notebook is not listed, you do not need to change the Advanced PC Card settings.

AST PowerExec 3/25SL

Chicony SubNote 486

Compaq Concerto

IBM Port Replicator 1

Twinhead SubNote 486SLC

IBM PS/2E 9533

IBM ThinkPad 360 CSE

IBM PS/2 ThinkPad 755 CD

Notebooks with PC Card controller (TCIC-2/N) from DataBook